LM1458 Replacements?
I typically prefer tube amps, but I have a Music Man amp from about 1979 that sounds great. It has a solid state preamp section and tube power section. The preamp section uses LM 1458 op amps. Any...
View ArticleClik here to view.
virtual motion device
hii have pxie-1035, pxi-7350 now but i can't use itI'm looking for the "motion control" function. i download ni motion 18.0, ni-DAQmx, NI-IMAQ and i use window 10but when i right-click on Devices and...
View ArticleEtherCAT Motion Control without Softmotion
NI already announced that the motion cards reached end-of-life and no replacement is planned. The motion control softwares also reached end-of-life: After Softmotion 2020 there will be no new version...
View ArticleProblem: PWM signal not well rectangular
Dear all, I run program in order to generate PWM signal. However the obtained signal shown in oscilloscope is not well rectangular.if you have any idea I tried many sinusoidal frequency, many pwm...
View ArticleMotion Control for STP-MTRD-23; String of Commands Locks UI
Hi, I made a post last week in Instrument Control about creating a motion control program for two Automation Direct Stepper motors that runs on a cRIO 9045. I have since taken the advice from that post...
View ArticleEtherCAT error - 2147138467 when switching third-party device to Safe...
Hello everyone.I'm trying to build communications between a cRIO-9040 controller and a third-party device, Faulhaber MC5005.The EtherCAT slave device were detected successfully after importing the ESI...
View ArticlePCB Sbrio-9608
I'm looking to buy four sbrio-9608, do you have any you want to unload or do you know anyone interested in selling
View ArticleHow to measure a stepper motor Current and Voltage
I have a need to measure the current and voltage being used by a stepper motor while it is running. It is a 5 wire stepper motor wired in series. Can anyone explain to me how to do this? ThanksTerry
View ArticleNI-9505 Life Cycle Status and/or alternatives
HelloDoes anyone know if NI-9505 is still on production and the current life cycle status of the product?I've been looking at te webpage and I can not find the product nor any other spare part that...
View ArticleCode example ni DAQmx AKD in c or python
Hi im very new to the NI suite, but I have a solution consisting of 2 AKD motors, an ATI torque/ force sensor which all are connected to the “NI USB 6521 DAQmx “. I’m using NI’s python lib nidaq (ver...
View ArticleSoftMotion Error -70225 when attempting to stop a move
I am encountering error -70225 when attempting to stop a straight-line move when a limit switch is encountered. The error states "Error -70225 occurred at the Stop Move when executing 'Stop' on Axis 1...
View ArticleFailure to connect multiple servos over EtherCAT
I'm attempting to control a set of 4 servos/drives with an NI-9039 and can't seem to operate more than 1 drive at a time. I can connect to and operate any of them individually but once I daisy chain...
View ArticleEthernet Connected ISM7412 Error 52023
Hey all, We have an old program that was written in Labview 2014 Win 7. The computer hard drive had a catastrophic failure and is unrecoverable. I am trying to resurrect the control on a new hard drive...
View ArticleIllegal board iD error for PCI-7354
Hi everyone, I have a system based on LabVIEW Real Time 10.0f2 with a PCI-7354 built in 2009, running until last week.Now the controller stops working at the initialization of the four axis. We...
View ArticleHow do I control Newport's CONEX-CC using LabVIEW?
Hi, I'm a college student who wants to operate the CONEX-CC device of Newport. I want to use LabVIEW to operate CONEX-CC, but I just started studying LabVIEW, and I want to get help because there are...
View Articleproblem accessing Kollmorgen AKD Drives using CANOPEN and XNET
HI, I have been using LabVIEW for 15 Years but have now got a project using Kollmorgen AKD drives. I have a cDAQ 9185 chassis fitted with a NI 9862 CANOPEN module. I can talk to the drives using the...
View ArticleGenerate DC voltage to control an electric motor
Hello. I'd like some help to generate DC voltage to control an electric motor using a NI PXI-6221 M Series Multifunction DAQ and an SCB-68 Connector Block. I'm plugging one wire of the motor to "AO...
View ArticleClik here to view.
Dust-free environment equipment manufacturers must see the three elements...
For many manufacturing industries, it is necessary to build a dust-free purification workshop, but different industries and different products have different requirements for the purification level of...
View ArticleCan't find MGMotor Control
I'm trying to embed Thorlabs APT to labview and following the instruction provided by them Microsoft Word - Guide to LabVIEW and APT.doc (thorlabs.com). There's a step to insert the MGMotor Control...
View ArticleMotion Control - Labview and Beckhoff Twincat (PLC)
Hi all, After some research, I found a good Softmotion alternative: it is the motion control with the Beckhoff system. All you need is a Windows machine that is acting then as the EtherCat Master and...
View Article