Controlling Stepper Motor with Analog Outputs
Hi, I am working on a project where I will need to control a stepper motor using LabVIEW with analog outputs. I am using a NEMA 23 motor with the M542T driver and I have the NI 9264 voltage module and...
View Articlespeed control of Switched reluctance motor
hello i am now able to control the motor in open loopbut to make it as closed loop, i have to measure the speed of motor and given as input to controller in labview to control the speed of motor....
View ArticleControl of Thorlabs K10CR1 cage rotor device blocking entire VI
Hi all,Rather specific issue but I wonder if anyone has had similar problems. Trying to determine if this is expected behaviour in Labview or if something else is at play. I'm using a K10CR1 motor...
View ArticleClik here to view.
Maxon EPOS4 using EtherCAT interface
Hello community. I'm currently implementing Maxon EPOS4 motor driver with cRIO EtherCAT interface. As there is no SoftMotion Drive Interface (SDI) support for EPOS4, I had to manually configure the...
View ArticleMultifunction I/O Device to control a hydraulic piston
Hi, I am a student of software engineer and I am new to NI hardware utilization. Basically, I want to control a hydraulic piston in a tractor, this needs to be done by a computer and using Python. Can...
View ArticleGECO Motion - a motion controller specifically designed for LabVIEW
Alright folks ... this is what happens when you notice a problem long enough. You make a solution for it!Motion control is an integral part of any automated test or control application. LabVIEW is a...
View ArticleSoftmotion migration to third-party
Hello, I'm currently trying to migrate my projects from NI Softmotion project to a third party because you unfortunately end Softmotion development (which is a sad decision). Kollmorgen AKD drives were...
View ArticleClik here to view.
The motion control program with NI9512 with chassis 9148, PLEASE HELP ME
Hi everyone, I'm a beginner of NI system, I was using PLC to building project. Rececntly, i want to use NI9512 with chassis 9148 to control a step motor for my project. But the many problem comes up....
View ArticleControl of TMCM-140-42-SE module stepper motor with Labview
Hello, I am a beginner in LabView. I have successfully controlled TMCM 140 42 SE module with TMCL software. But since we are trying to automize the entire project with LabView now I want to control...
View ArticlePCI7344
Dear allWe are looking for an old PCI7344 card (4 axis card driving motors) over 15 years old (copyright 2001). Indeed, when we use a newer PCI7344 card, we have driver / firmware compatibility issues....
View ArticleWiring myDAQ with L298N motor drive to control DC motor
Dear community, for a laboratory application, I need to control a DC motor with a computer (on/off/direction of rotation/speed). I have an electric motor from an old stick blender, a NI myDAQ and a...
View ArticleHelp controlling DC motor with a PID controller and external controller
Dear all,I am relatively novice with LabView. I have made a code to take measurements of an experiment where I have an electrical machine with some superconductors in it. I have set some Hall sensors...
View ArticleClik here to view.
NI PXI 7340 : Motor starts and stops immediately, doesnt reach target value
Recently, i have upgraded OS in the PC. Max configuration has been restored. New drive has been configured in velocity mode. When i try to run the motor, start vi starts the motor but it stops suddenly...
View ArticlePID control with 0-10Voltage LVDT
Hi everyone, In my case, I have a LVDT with 0-10V output range, which causes a problem that if I set the start point to be at some Voltage between 0-10 V (say 9 V) and then start moving, then the...
View ArticleOutput value does not equal to the position but proportional to it
Hello everyone, I have a servo-valve, servo-amplifier and LVDT closed loop system with 10V output and input modules. When I output a value (say 5 V), the actuator always go to the position of half of...
View ArticleControlling ISM-7413 Stepper Motors with CRIO
I have successfully controlled my ISM-7413 stepper motors by connecting them via ethernet switch to my host computer and connecting to their specific IP address that is physically set on their drive....
View ArticleClik here to view.
Increasing stepper motor torque/speed with MyRio FPGA
Hello, Quick question I have Microcon SX-16 2 phase stepper motor connected directly to MyRio FPGA trough connector MSPC, DIO lines 0-3 where should be 5V. Program that runs this motor has one case...
View ArticleServo motor control
Hi, I want to control 2 servo motor. Can PXI-7344 directly control these motors without additional servo drive? Thank you in advanced!
View ArticleHow to control stepper motor by labview?
Hi. I want to control stepper motor to use linear actuator. But I can't do anything. I use myRio. And I also use motor driver m-224. my actuator is sbc-ls4075. If anybody suggest the total algoritms, I...
View Articlesbrio with external motor drive
Hello Everyone, I have motorized stages from PI (Physik Instrumente) LP. These motorized stages work very well when I connect them into PC by Ethernet cables. We're planning to use sbrio RT target to...
View Article