Advice on Stepper - Encoder Setup
Hi all, I am using phidget stepper motors and encoders to create a vending machine style XY axis. I would like to have several buttons on the front panel that will correspond with an encoder value for...
View ArticleClik here to view.
Using Arduino to control stepper motor driver + stepper motor with LabVIEW
Hello everyone, I am trying to create an interface for controlling an Arduino Uno connected to a stepper motor driver carrier that is wired to a stepper motor using LabVIEW 2016. The Arduino is...
View ArticleNI cDAQ 9174 with NI 9503 Module unsupported module
I am currently trying to drive two stepper motors using two NI 9503 Modules plugged into a cDAQ 9174. I have the motors plugged into the modules, but they are being detected as unsupported modules in...
View ArticleController SMC100CC Set home type value
Hello, I'm currently using a SMC100CC controller and I would like to change the home type value on labview but i do not understand what MZ switch and EoR are ? I've seen the user manuel with the...
View ArticleClik here to view.
enable EtherCAT communication without using softmotion
We are currently using the NI cRIO as a master and ELMO’s servo motor driver (third-party) as a slave for motor control through EtherCAT communication. After completing the cRIO network setup according...
View ArticleNI Motor different Zero Position every time
Hi,I am using AKM11B-ANCNC-00 motor with AKD motor drive, NI UMI and motion control card. Every time when I power up and give command of zero absolute position from NI MAX software, the motor achieve...
View ArticleMaking the imported excel file is read and judged by segments, and the...
Hi everyone!I am rookie in labview, here is my problem.I use labview to control googoltech stepper motor, three-axis linear interpolation motion control and arc interpolation motion control have been...
View ArticleLabview-canopen interface USB 8502 control EPOS4 maxon motor: acquisition data
Dear all, I am quite new with labview and I need to develop a high level control scheme to impose torque input to two different maxon motors (EC60 flat motor, EPOS4 Compact CANopen 50/15 driver).To...
View ArticleNI 9503 modules not showing under NI cRIO 9063 devices and interfaces
Hello, I am trying to connect an NI 9503 into my cRIO 9063 to drive a stepper motor. I have been trying to find the module in NI Max to confirm that it is working, but it doesn't show up under devices...
View Articlexyz positioning stage
Good morning,i'm pretty new to LabView and love it. I'm interested in setting up a x-y-z linear stage driven by NEMA 23 stepping motors. With this aim, i wanted to buy some hardware from NI shop, but i...
View ArticleGeneral query about NI driver, controller, and C module
We have a cRio 9047. We are preparing to integrate an NI SMD-7615 and motor (it's NI but I don't remember which) with the controller for a redesign of an application currently using a non-NI motor and...
View ArticleFeedback control system- Closed loop for voice coil actuator
I am working on a project to design and develop a closed-loop feedback control system using PID. Current device (no PID)The device is a vibratory device made of a linear actuator that is connected to...
View Articledriving a stepper motor
hi guys ;i am working on a stepper motor , and i have to calculate the distance it runs through ,am working with Aduino board . how is that possible ?
View ArticleNI cRIO 9063 w/ 2 NI 9503 simple movement
Hello, I have just started learning the soft motion module, but I cant seem to find very much in the way of tutorials or guides for the program. I was wondering if anyone could help me with how I would...
View ArticleHow to control my Proportional Solenoid Valve using 0-10V from NI9264
Hi I have 3 proportional Solenoid valves from Cole-Parmer Cole Parmer DIrect-Lift Propertional Solenoid Valve.It requires a 0-30 VDC input for proportional operation. They are suggesting to buy their...
View ArticleElectronically Controlled Proportioning Valves
I am completely new to LabVIEW and creating VIs. I need to monitor and operate three Omega PV series, Electronically Controlled Proportioning Valves. These valves operate on 0-5 VDC. Im trying to build...
View ArticleProportional valve connection diagram
Hi Everyone, I am trying to understand how to wire my proportional ball valve to the PSU and DAQ devices.----------------------------------------------------------I am using the following:1....
View ArticleStop Motion EtherCAT Drive
I am using two Mitsubishi EtherCat Drives and servos. I am starting a coordinate move with the two axis. I have a DAQ engine that is monitoring load cell outputs (on an RT target). When a load set...
View ArticleLabVIEW interface with Lti Servoone driver via PROFIBUS
Hello all, Currently I am working on a torque and speed testbench project. The main task is to establish the communication between the AC servo motor's driver which is from LTi moton company and the...
View Article