encoder make microstepping drive blink red
Hello, I am a French intern, so please be indulgent =)I have a problem with an rotational encoder (connected to a step motor T22).We also have a Microstepping drive but thi on blinks red constantly....
View Articlecomment faire la connexion d'un radio commande FLYSKY acec MyRio?
comment faire la connexion d'un radio commande FLYSKY acec MyRio?
View ArticlePlease I need help urgently
Hello everybody I am stuck in project now. and I need your help kindly. I have Motor Controller which is RS160D with 2 geared dc motors. The RS160D has RS232 serial port and I need to move the motors...
View ArticleError -77124 when trying to use contour move
I am trying to move my motors using contour move ExpressVI. Unfortunately, it gives an error code of -77124. On opening the ExpressVI, I found the problem to be with the invoke node which starts the...
View ArticleTamagawa Absolute Encoder interface
Hi, I try to interface a Tamagawa TS5669N124 absolute encoder that come with Allen Bradly motor. (attached datasheet). There is only data+, data-, ground, 5v+. So it's not SSI Encoder (no clock+-),...
View Articlepci 6014 dc motor setup
Hi, I'm using PCI 6014 and USB 6211. I have motor driver (MD10C). There are 3 connections required which are DIR, PWM and GND. Those connection should be connected to PCI 6014.Therefore, I have several...
View ArticleWhy am I getting error -70027 with SofMotion?
I am trying to run a LabVIEW RealTime application that is using SoftMotion. I created an axis in the RT target of the project. Every time when I am using the axis with SoftMotion functions and run it...
View ArticleTorque Control Mode Enable (Dynamixel MX-64)
Hello!! I am working on a project in which I need to control the torque of the Dynamixel (MX-64). From the datasheet I read that to control the torque we need to set the Torque Control Mode Enable to...
View Article3Ds max
Hello Everyone, I'm very new to lab view and I'm just learning. I'm trying to design a human arm in 3D for simulation purposes but before I take any wrong steps, I have a question. Can I use 3Ds max to...
View Articleni7340
I want to use NI7340 4axis motion card with IAI Pulse controller for my project.According to IAI drive its need 24vdc for control signals.I am using PCON-PLB controller for this project.I am worried...
View Articleism 7413
Helo all can i control the ism 7413 stepper motor using cvi?I have searched the product docs and found only labview support Thank for advance Gabel daniel
View ArticlePCI-7354 初始化
Hi All 目前遇到關於PCI-7354軸卡問題，詢問各位是否有遇到類似狀況， 設備在生產過程中，若遇到設備發生狀況時，User會按下緊急停止， 程式會下達停止的命令，驅動器會被斷電， 當故障排除後，設備進行復歸動流程時，完成復歸後下達歸零的命令 但發現下達歸零命令時，馬達回傳的位置不在設定的位置上， 此時，透過NI的界面對軸卡下初始化的命令後，在進行復歸動作後並歸零，馬達回傳的位置就對了，...
View ArticleIs there a VI that replicates MAX settings?
Hi everyone,I'm looking for a vi that can be used to set the same motor features that can be set with MAX. It would be great to run a vi like this rather than setting up MAX each time in advance of...
View ArticleProper DAQ Module for Celesco SP2 or SP3 String Pots
Hi! I am currently looking to expand our lab's capabilities by adding string pots to our sensor tool kit. I came across a string pot that will work for us, namely Celesco SP2 or SP3 (either one). Here...
View ArticleBad resolution
Hi,I am using example project for NI 1483 adapter module, I have changed it to 8-tap 8-bit mode, I am using camera HXC13 Baumer, I am obtaining some image, but it looks very bad and obtained resolution...
View Articlemodel simulink
Greetings. here I havea question,I have made asimulinkmodelonmatlab2009,a UPSthat powers an electric motor, soinverter/motoroperation,and wishto place an order, a switch (switch)for...
View ArticleNI Motion - Smoothly moving motor through defined positions
I am using a steeper motor to adjust the angle of a continuously variable neutral density filter for a optics project. By adjusting the angle of the filter, the transmission is varied. The aim is to...
View ArticleKnowing time a breakpoint occurs to synchronize external instruments
Hi, I'm using a PXI system with a PXI8196 controller, a PXI7350 Motion Controller, a UMI-7774 and my application is written in VB6.I need to move a stepper motor and its position is measured by an...
View ArticleISM7411 Ethernet streaming protocol
I need to control ISM-7411 Ethernet Stepper Motor with Ethernet streaming commands.I tried to find documentation about this, but without result...ISM-7411 use a standard protocol and what it-is ?Is...
View ArticleSingle Axis Move Example - where to get?
Hi, I'm using the Control Loop (Fixed Point PID) Library and I use it with an NI9514-Module to control Position and Velocity of a motor. The SoftMotion-Help often refers to the "Single Axis Move (with...
View Article