what are hardwares needed to control my servo motor?
I have cRIO NI9024 + NI 9118 and I want to control my servo motor (480V 7500W 48Nm) that its like in this link.what is the options to contol it?- if using EtherCAT. What is the model of drive that...
View ArticlePCI 7344 behaving erratically, random servo movements
I'm using a PCI 7344 to control a 3 axis test stand. Today when I initialized it with out modifiying any settings it didn't work, just kept moving servos randomly even when controlled by MAX and a...
View ArticleClik here to view.
How to send data to a website by using http client in labview?
Hi guys. I have to calculate distances between ports and i have more than one thousand calculation. I dont want to do this by hand. I prepared an excel sheet. First column include the first port and...
View ArticleKollmorgen WorkBench Hardware Enable Problem
I am trying to connect a AKM53L motor with an akd servo drive. Using the kollmorgen workbench software, I can see that the software is enabled and that there are no faults present. The hardware enable,...
View ArticleControl Stepper Motor Using NI Motion
Hi all, I need to do a real simple application of a stepper motor rotating at steps 60 degrees apart, and after 360 degrees, it comes back to where it started (home/0 point). I have a PXI with a NI...
View ArticleCompatibility windows 10 fr
I am running windows 10 fr, LV 2016 en, it's possible to operate an ISM-7413 engine, otherwise, what configuration I will need
View ArticleLimit switch event
Hi All, after searching a bit I am turning to the knowledge base and the "web wisdom" hoping for a solution. The setup is consisted of 2 stepper motors, drived by two separate SMD-76xx drivers (one for...
View ArticleWhich (dc) motor controller has the best Labview support?
I am looking for a good solution to control a two DC motors over a fieldbus (CAN or EtherCat) through a pc. NI Softmotion seems to be great for this. But it seems I need a realtime system for it, a PXI...
View ArticleClik here to view.
MOSFET selection for BLDC motor drive
This question is related with the one I asked sometime ago about the heat generated when driving a BLDC motor BLDC drive inverter circuit problem.The problem is, the MOSFET chip got heated up...
View ArticleLabVIEW with Modbus RTU-Stepper motor
Hello All,I'm new here, I wonder if you can help me out,I have a stepper motor (bipolar-4wire) and a motor driver both from LAM technolgies. The driver interface is usb and comminucation protocol is...
View ArticleAsking about the controlling servo motor by NI 7350 controller
I have already gotten a new machine and My prof told me to contact to run the servo motor , we got 3 motors to control 3 axis to move the postion like 3d printer . And we got ni motion 7350 controller...
View ArticleHow to write to Kollmorgen AKD
Hello, have to set up a system that uses the following Kollmorgen components: Servomotor AKM24D-ANBNR-00Drive AKD-P00306-NBCC-E000Motor (AKM13C-AKCNGD00) I am interested in creating with LabVIEW an...
View ArticleHow to solve following error in open loop stepper motor motion system
Hello! I am pretty new at this whole thing and I am trying to troubleshoot a problem. Our setup is as follows: cRIO 9022 with stepper motors, and 9512 modules. Now we run our setup for weeks non-stop...
View ArticleSingle-ended or differential signal from motor
We are using a brushless DC servomotor (4490H024B) in combination with a three channel digital output encoder (IE3-1024L ) from Faulhaber.We want to connect the A, B and I lines of encoder (IE3-1024L)...
View ArticleControl of a 2-axis stepper motor system by Vision Builder
Hello, is there a way to control 2 stepper motors via Vision Builder? What components do I need? BR, Klaus
View ArticleSolid woks y Labview
Buen dia Tengo instalado el Solidwoks 2016 al igual que el Labview 2016, instale el modulo de NI Softmotion mas sin embargo no puedo realizar la coneccion de estos 2 sofware, Me prodrian ayudar por...
View ArticleUnable to find encoder resolution of myRIO mechatronics kit geared motor
Hi,We purchased 5 myRio Mechatronics Accessory kits from NI few months ago. When I was building new experiments for the lab, I followed myRIO project guides here . However, I couldn't find any...
View ArticleHow to control a ac servo motor using Labview?
Hello, I am new to motor control with Labview. I have a Panasonic AC servo motor with driver Model MCDHT3520BA1.I would like to control using Labview. I have NI-cRIO 9025. I want to use it Position...
View ArticleControlling XY table using a third party hardware and software or NI system...
Hi all, I have to design an XY table 1000x1000mm(could be bigger) to measure values of LED panels in different points moving the sensor(Thorlabs) and I am trying to decide which approach would be the...
View ArticleVoltage drop to servo drive
Am using a PCI-7340 to control a drive for a motor (drill spindle) with no feedback on one axis, so have the axis disabled and am using the DAC output to set specific voltages. With the analog cable...
View Article