Potential Count Lost using Motion Control PCI-7350?
Hi, I am currently using PCI-7350 with the latest firmware to drive a Faulhaber 2237 series motor coupled with a GSI 6000 seires encoder. I have no problem when moving or finding the index when the...
View ArticleDriving an arbitrary motor with SoftMotion's FOC
I'm currently trying to drive a brushless servo motor using the 9502 and 9411. I have everything set up, but the motor starts vibrating whenever I enable the driver. It's also drawing way too much...
View ArticleRunning N31HRHJ Motor on PXI 7330 and UMI 7772
Hello guys, I'm a beginner in Motor driving, learning this thing since a week. I read a lot of manuals and documentations and examples about this issue, but I still can't get my motor to run in any...
View ArticleCommunication between Labview and PIC
Hi,I want to send commands from the Labview to a PIC micro controller that should control a tracker (to turn a motor right or left, etc.). I would like to know what are the options to implement this. I...
View ArticleSoftMotion Express VIs vs. Function Blocks
Hi, Are there any differences between SoftMotion's express VIs and the function blocks? I plan to drive a servomotor via an NI 9505. The NI examples show how to use the function blocks, but I've been...
View Article9148 chassis, 951x modules, and SoftMotion
I'd like to develop a motion control application using C series modules without using LabVIEW Real Time. I've found a few sources pointing to a possible solution, but am having trouble finding detailed...
View Articlesinusoidal commutation?
Hi, Is there any support/examples for sinusoidal commutation for use with a cRIO? I'm assuming we could right our own if we wanted? We have a DC brushless connected to a 9502. We are going to drive...
View Articlesynchronize NI 9514 with NI 9401 for digital output
Hi, I need to write a code to trigger a laser for a PIV system. I'm using the NI 9514 with an AKD Drive to control a servo. I need to send a +5V signal to trigger the laser at a specific angle of...
View ArticleControling wheelchair by speech command using Neuron Network in labview
Hi all,I'm doing project about "controling wheelchair by speech command using neuron network in labview". I found some informations about controling whelchair combine with function microsoft speech...
View ArticleThird party ethercat motion controllers
We are looking for recommendations for 3rd party EtherCAT motion controllers to integrate with a cRIO system. I am aware of this article. We will be driving 5 rotary brushless motors (moving them a...
View ArticleLabview system identification
Hello sir, I am currently working on whole vehice system identification.For example I have on road suspension input and output data.and I could get the some tranfer fuction model of same system. So is...
View ArticleBuilding a simple shutter - beginner question
Hello, I want to construct a simple shutter (leaf or diaphragm) for a 5cm lamp aperture, and to interface it to a computer so I can program the shutter behavior over time.I have never done such things...
View Article2011 9501 C-Series Example broken wire/property
Hello, I'm trying to run the 2011 Position Control (open loop) example for the 9501 module, but it is showing a broken connection to the "Time Interval" property of the "Straight-Line Move" property...
View ArticleAttempt to communicate to Newport MM4006 controllers via serial in new labview
I am attempting to communicate to a Newport MM4006 motion controller via labview, however the drivers built are for version LABVIEW 6i, and was worried about backward compatibility with the current...
View Articlesoftmotion module using 9505?
HelloI need some help regarding softmotion module.I am using compacrio 9074, drivers for my stepper motor 9505 and DIO module 9504 for my encoders input.I am using softmotion module to create the...
View ArticleUser-Defined Variables, FPGA mode, and SoftMotion 2012 + NI 9505
Hello, At http://forums.ni.com/t5/Motion-Control-and-Motor-Drives/Softmotion-and-NI-950X-Module-Compatibility/td-p/2166242, Nathan said:NathanK wrote: The glue code that connects Softmotion on RT to...
View ArticleQuerying the SoftMotion table size programmatically
Hello, Is there a way to obtain the size of a table buffer (as in the total capacity, not the "Space Available") at run-time?. I'd like to benchmark different buffer sizes + sample rates, and I'd like...
View ArticleNI Motion with 3rd party cnc controller
I want to run my own CNC machine with NI motion toolkit and labview.But i don't knew if I can use labview or not , I want to get the advantages of NI Motion toolkit to build my program and send the...
View Articlestepper drive 9501 example?
HelloI am using an example of stepper drive 9501 to drive my stepper motor! I have two questions:1. I cannot see any RT.vi.? where do we have to give as in position or angle input?there is no RT.vi2....
View Articlehow to set x-axis of waveform chart to be real time
sir how to set the x-axis of waveform chart/graph to be real time. DAQ assistant block is used to aquire the analog signal(voltage), that chages with different load.this voltage signal is required...
View Article