Clik here to view.
Table and Waveform Chart
Hi all! I am recently use LabView and SoftMotion for SolidWorks.I have some problems.I want use move contour, but I don't know what is "table" and how it use. How I can connect Waveform Chart to move...
View Articlerobotics
sir i m using sbRIO9631 for my project and i m new to this too.And one part of it is to interface a Passive Infra Red (PIR) sensor with TTL output os 0 to 5v to sbRIO.I have declared the PIN and I have...
View ArticleHelp with choosing the right hardware
Hello, I would like to know what hardware sollutions from NI are best suited for my Master's degree project, which is a motorized crane for a video camera (basically a robotic arm with 5 axes). What I...
View ArticleSoft motion error.
When deploying any motion command to a CRio using softmotion. It fails to deploy NIMC.create.vi Any one else seeing that. We are using labview 2012 and NI 9512 modules. We are trying to just follow...
View ArticleNI 73xx motion control, maximum velocity
Hello! Last time I was testing a new step motor controller. I discovered, that when I set the velocity higher than 2000steps/s, the speed doesn't increase more than 1968steps/s. I tried to set many...
View ArticleQuestion regarding functioning code
Hi, The code I am attaching to this message is working. I started from the DAQ assistant and then modified it. Its function is to read a pressure and drive a proportional valve to maintain a...
View Articleconnecting stepper motor to the module 9512
Hello,I must do project in LabVIEW.I use the compactRIO with module 9512 (Stepper Drive Interface Module with Encoder Feedback). I built a small program of this tutorial...
View ArticleIAI PCON_C
Hi, I'm looking for a LabVIEW driver for IAI PCON-C motion controller.It can be controlled using serial or by MODBUS. (both using VISA)The protocol is complicated and a lot of digging is required, so I...
View ArticleBreakpoints During Contouring
We are moving laser head using Contouring mechanism and it is working good.Now we need to Turn laser on/ off at certain points. Is it possible to embed that information on buffer with the position data...
View ArticleHow to integrate Analog Input (acceleration) on line
I'm using crio 9022 to measure analog input acceleration through FPGA module.Actually I need the velocity rather than acceleration.I'll use velocity in a controller based to generate analog output to...
View Articleanalog input issue with the pci-7332 and umi-7774
Using a pci-7332 in combination with the umi-7774 for driving a stepper motor. Have an issue with the analog input being 0.488Vdc off from the actual reading. I've tried several voltage sources only...
View ArticleSoftMotion 2012 Example update
Hi,I noticed that the examples shipped with NI Softmotion module is not updated. Although the directory has been changed, the example still points to LabVIEW 2009 folder. I also would like to ask...
View Articlewhy does vi execute in HIGHLIGHT mode only? Does not RUN from front panel
This is extraordinarily puzzling to me... The attached vi sends a serial command to a motor controller. Command has the form /1V5500P0R, where the /1 means "motor 1", 5500 is the velocity, and the...
View ArticleAKD驱动器的模拟输出如何控制电机的位置和速度？
很多伺服驱动器通过脉冲个数控制电机位置，脉冲频率控制电机转速。AKD伺服驱动器通过接收PXI7350等板卡的模拟信号控制电机，如何实现对位置、速度的控制？考虑到外部环境，它的精度是否容易受到外部的影响，精度如何保证？谢谢
View Articlevi with move deploys with errors
We are using a compact rio with a 9512 and a P7000. We can use the interactive test p[anel from the axis and the motor is controllable as expected. But when we create a vi with a move function block...
View Articleload cells
Dear all, I am new here, I want to know what exactly I need for connect a Honeyweel Load Cell model 31. Can someone help me? Thank you very much, Laia
View ArticleNew PCI-7358 used on old system issues
Hi all, Many years ago I setup machines with several PCI-7358 cards using NI-Motion 6.1x and LabVIEW 7.0 - a card failed so I purchase a replacement. The replacement has the current firmware version on...
View ArticleDELTA ASDA-A2 DRIVES
Are the subject drives from Delta (http://www.delta.com.tw) compatible with any of the motion controller cards from NI? 4 Axis Acceleration, Velocity and Position control is desired.
View ArticleDefault digital line outputs
Does anyone know how to set the digital port line outputs (when used as outputs, not inputs) on a 6013 board to a default state. My problem is that I am using this board to enable a drive but if the...
View ArticleControl of Linear Actuator using USB 6341
Can I use USB-6341 to control a Newport LTA-HS actuator for simple linear motion. How would I go about doing this?http://search.newport.com/?x2=sku&q2=LTA-HS Please explain in simple terms. Thanks
View Article