nudrive command problem
Hi, We have this nudrive that we use since 2004 on a production station. We didn't change any variables (the setup is running in this state for years) and it suddenly stopped to go forward. Even if I...
View ArticleWhich RTOS can be used in Raspberry-pi board ?
hello,I am working on a robotic project, and i am using labview robotics module as my tool. Since i have a udoo dual core board with me(atmel ARM cortex A9), i want to use this board as my RT target. i...
View Articleerror #-70149
Hi, I tried to implement the exact labview code found under 4. Move Types- Coordinated MultiAxis Motion from the following link: http://www.ni.com/white-paper/3367/en/#toc4, except I am using 2 axes...
View ArticleClik here to view.
Is SERCOS supported by NI-Industrial Communications for EtherCAT?
Hello, The EtherCAT standard supports several different Mailbox Protocols: (source: http://www.ethercat.org/en/technology.html ) However, the following page from the LabVIEW IDE (LV 2013 SP1 +...
View ArticleSpecifications of servo valve, pump and power unit for a 200 kN hydraulic...
Hello Everyone, I am new to the forums and I hope this is the right place to ask my question. There are lots of people talking about hydraulic actuators and I think I will get my answer. I knew...
View ArticleDiscrepancies between following error readings in NI-MAX
We are currently investigating the source of following errors in our systems. Maybe there is something wrong with our setup. We are using stepper motors with third party drivers and incremental...
View ArticleNI Stepper Motor not putting out enough torque
So I have a motion control system with a P70360, UMI 7772, PXI 7332, and a NEMA 23 stepper motor with 380 oz-in. The purpose of the set up is to rotate horizontally a testing fixture and hold it in...
View ArticleSoftware enable for Kollmorgen AKD using LabVIEW
Hey all, I'm relatively new to motion control, and feel like I must be missing something...I have a PXI chassis with a 7350 card connected to a Kollmorgen AKD as described in the Getting Started guide....
View ArticleHoming in APT
Hello everyone, I am working with DC motor using ATP interface. It is working fine but I do not get how to homing my motors yet. I mean that my motors go from 0º to 90º step by step and I want they...
View Articleset acceleration
Hello, I had developed a .dll to control a 3 axis machine. During reference home procedure I want the machine to find the home limit and reverse the direction within a certain space. For this reason I...
View Articleencoder reset for NI 7358 card
I am using 7358 eight axes motion control card. I am trying to read incremental /quadrature encoder reading. I am using a motor built with quadrature encoder giving 4000 pulses per revolution. I am...
View Article7332 is not detected in MAX
Hi, We have a PCI NI7332 motion controller purchased with us. We installed the drivers and softwares from the cd that comes with the package. The problem is PCI NI7332 showing as NI7330 in MAX ....
View ArticleMotion control: PXI 7350 controller and UMI 7774 to interface with...
Dear community, This is about Motion control in Labview: I try to control a step motor by using a PXI 7350 controller and UMI 7774 to interface with third-party driver UDK5114NW2. The problem is 5...
View ArticleHow to access all the I/O variables for ELMO drive
Howdy All, I am not sure if this is the problem with the ELMO motion controller or with the LabVIEW configuration, but I will post this anyway. I have a motor controller (ELMO Gold Solo Whistle) for...
View ArticleAKM Brushless Servo Cables
Hello All, I am interested in buying the AKM Brushless servo, particularly the AKM2X and AKM3X series. I intend to use these motors with a third party drive. However the only accessories that are...
View ArticleBode plot for C series cRIO
Hi all, I have a DC motor NI 9505, and cRIO 9024. How is that possible to have the Bode plot for the motor since it is controlled in FPGA. Now I have the motor running by the PID controller in FPGA but...
View ArticleClik here to view.
Kollmorgen AKD problem of enable
Hi , i try to use the Kollmorgen driver AKD-P00606 with motor AKM32HI don t know have to enable the hardware . I try to use WorkBench but only i juste enable the software . How can i do please to...
View ArticleDo I have to load torque, velocity, accel/decel, following error every time?
Hi,This is my first project with NI-motion. We use NI 73xx library. I would like to know in every move, do I have to load torque, velocity, accel/decel again and again if I don't change these...
View ArticleModbus installation instructions incorrect. What are correct instructions
Hi all, I'm trying to install the Modbus driver, but the NI instructions seem out of date. They don't match what I see on my Windows 7 64 bit machine with the trial Labview 2014 (64) installed....
View ArticleXY board 60 x 60 mm with easy LabVIEW interface
I am looking for a vendor of an XY-board that can travel 60 x 60 mm,and with an easy interface towards LabVIEW. Anybody got somerecommendations ?Martin
View Article