NI softmotion: vitesse du moteur est limité à 51rev/sec
Bonjour à tous, Dans mon application, j'utilise un CompactRio NI9074, un module NI9514, un AKD EtherCAT et NI SoftMotion 2012 pour piloter un servo-moteur de AKM23F. J'ai réussi à piloter le moteur...
View ArticleAccelaration for a stepper motor
Hello,I am controlling a stepper motor through a circuit which converts analog voltage to frequency. I use NI6009 USB for generating the voltage for a Voltage to Frequency Converter circuit. My problem...
View Articlecontrolling XY table using a stepping motor
Hi all,I want to control an XY table using a Lang MCL 2 stepping motor and for that I'd like to use a pre-made toolkit instead of programing all using DLL's. Any suggestions?!Best Regards,Seno
View ArticleFlexmotion dll interface in .NET 4.0
I have a working solution for an older configuration that needs upgrading to a new PC target. The old configuration uses Flexmotion.dll (NI-Max version 7.0.0) to interface to a PCI-7344 motion...
View ArticleStepper Motor Automation
Hello, I am new in Labview and has been tasked to automate a stepper Motor RS-232 to move clockwise and anti-clockwise with varing speed to cover 82cm distance with the ability to read the time...
View Articlepowerflex 70, PF70 communications
I know there are already at least two similar questions about this in the past, but the newest one I found is from 2007. Does anyone have experience communicating between (CRio and/or LabView) and an...
View ArticleRotary Encoder
I am planning to developed Test bench for electrical motor testing using NI Labview and hardware. I have this old rotary encoder of which picture is attached. I want to get technical specification of...
View Article™DUBAI ℯscorts Sℯrvicℯs™+971552447866 Indian ℯscorts Girls in Dubai
™DUBAI ℯscorts Sℯrvicℯs™+971552447866 Indian ℯscorts Girls in Dubai High Profiℒℯ ℯscorts iℕ DUbAI, Pakistani ℯscorts ℂall GiRℒs iℕ DUBAI?Indian ℯscorts in Dubai | Indian Caℒℒ Girls in Dubai,™DUBAI...
View ArticleDynamixel MX64 servo:Labview help
Hi,I am trying to program the MX 64 servos (Robotis ) in Labview. I am new to Labview and having trouble to get this thing working. Trying to read and write data from and to the servo. I could not get...
View ArticleRecommendation which hardware would be best
Hi, I have a reed-switch telling me via voltage-spike when the control magnet is near. the reed-switch position and the control voltage can be freely chosen. This control circuit is then supposed to...
View ArticleLabVIEW with the Robotis Dynamixel AX
hi! im trying to use LabView to control 2 or more Dynamixel AX using the USB2Dynamixel. Has anybody some code example? how to control the speed? degree rotation? cause i just find some example but...
View ArticleLabview to input acceleration profiles on velocity drives
AMC recently suggested the use of labview to control a motor and servo I was interested in. I currently have AMC's B30A40 PWM servo drive, MBL3416E2 Brushless servo motor, and PS50A-LV power supply. I...
View Articlesimultaneous motor control
Hi everyone, I am building a robot with tank treads that has two motors: one for the left side and one for the right. I am using an arduino, xbee communication, and this motor driver. I would like for...
View ArticleOutputting square wave with NI 9263
Hello. I have a problem when trying to output 0 or 5V through the NI 9263. This should form a square wave and it should run parallel to a timed loop responsible for other control task. It should handle...
View ArticleDynamixel MX 64 Labview
Hi,I am using Dynamixel MX 64 servos in my project. I have 4 of them tied in series. P1,P2,P3, P4 represents degree rotation of each servo/axis. I am trying to run my code for set 50 values of...
View ArticleI'd like to know when NI-Motion will support platform x64
Hello. I'm making an application running on Windows-7 64bit with NI-Motion using Visual Studio 2010.It works well on Platform Win32 but I'd like to use it on Platform x64. As you know, NI-Motion does...
View ArticleClik here to view.
PXI-7350 Controller and MID-7604 Power Drive
Hello, I have some PXI-7350 Controllers and a MID-7604 Power Drive. I hope that someone could give me some advices. I'm trying to control 3 stepper motors (5-phase, not encoder or feed back). The user...
View ArticleSampling the same encoder data from two different hardwares
Hi, My system composed of 6 7358 motion control cards, 4 7654 servo motor drives, 4 7774 UMIs, and 25 brushed and brushless DC motors. These motors have quadrate encoder and the encoder signals are...
View ArticleStop/ Terminate doesn't work
Hi ,I have attached my code. I am not sure why the STOP does not terminate my program. I tried placing it outside while loop and case structure. Nothing worked. Thanks for any help,Sahana
View ArticleClik here to view.
Move Complete Signal doesn't work
Hello I used NI MAX to move moter in abs mode. When I click the start button in first time, then the move is compelete is normal output. But in the second time the signal is always not output....
View Article