7602
I am using a PCI-7342 controller and MID-7602 driver to control a stepper (no feedback). I configured the 7342 with the Automation Explorer and tried to start a relative motion on the stepper but there...
View Articlegalil dmc1840 with windows 7
Hello, I am trying to run the old PCI galil DMC-1840 card with Windows 7, but have a really hard time with it.The old GalilTools driver is not working. If I install GalilSuite and driver which goes...
View ArticleEdge detection for a counter.
Hi, I've input image into a VI and generated its edge-visible copy but couldn't succeed to find proble way to detect the exact number of pointed edge.Do you guys have any remedy to the situation.?...
View ArticleClik here to view.
Application Help
Hi guys, I need help for an appilcation we have here at work. We have a stepmotor (HT23-398D-ZAA) that include a 2000cpr encoder with STR4 drive and a PCI-7334 controller board. We had a UMI-7774 but...
View Articleproblem in solidworks and softmotion
Hi,i use ready solidworks design from the exmple ""and i build just a labview to read the lift sensor the problem that solidworks donot convert to active mode right click on my computer >>>...
View ArticleHow do you change the PID parameters in Matlab via a DLL?
Here is a brief as to what I am doing: -I am using a PCI-7342 board to control two axes via MID-7652 box. -I have created a DLL in C, which contains the flex_load_pid_parameters() function....
View ArticlePosition-based explicit force control with cRIO
Hello, I want to use a linear stage to apply a force on a sample with load cell feedback. I am using a cRIO-9074, NI 9516 servo drive and an NI 9201 for the load cell feedback. I have the following...
View ArticleReading IMU 6Dof in CDaq-9188
Hi,I want to ask about reading the data of IMU Digital Combo Board - 6 DoF ITG3200/ADXL345 in CDAQ-9188how can I do this ??Any one can give me suggestion please ?Thanks
View ArticleMotion Control using Stepper Motors: cRIO vs. PCI/PXI
Hello everyone.Firstly I want to introduce my problem for which I am looking for a solution: I want to control 2 separate stepper motors, both with encoder feedback in a closed loop...
View Articleencoder protocols
I never realized there were so many encoder serial protocols until I was tasked to investigate making some encoder test stands. The open protocols should not be a problem, but to service, repair and...
View ArticleControl DC Motor with Lab View
I'm a mechanical engineer who's never used Lab View before. For a project, we have to use Lab View to make a small dc motor start, stop, and reverse direction. I have absolutely no idea how to do this....
View Articlesolidworks & soft motion problem
hi deari am new user, i want simulate example in http://digital.ni.com/manuals.nsf/websearch/CBD0925AA14FCB8E86257A4E006BC609 in page 7 says2. Right-click My Computer in the Project Explorer window and...
View Articlesolidworks & soft motion problem
hi deari am new user, i want simulate example in http://digital.ni.com/manuals.nsf/websearch/CBD0925AA14FCB8E86257A4E006BC609 in page 7 says2. Right-click My Computer in the Project Explorer window and...
View ArticleCan USB 6009 generate PWM signals for DC motor control??
Can USB 6009 generate PWM signals for DC motor control? It is a closed loop DC motor control. The input of PWM i.e. duty cycle will be taken from the sensors attached with the motor and the frequency...
View ArticleClik here to view.
Repeated movement not executing
Hello, I am using a cRIO-9074 to move a Newport Stage. I want to do repeated movements in a Timed Loop (synchronized with scan engine).My code looks like the following: My code should do the following:...
View ArticleUpdating numeric Control with different values with array function
Hi ,I have attached my basic code . I want to run the code for 2 sets of numeric control values with a delay in between and loop it. Something like this abcInitialize P1=10; P2=20;P3=30;P4=40Run the...
View ArticleStepper Motor: Closed loop PID
Hello everyone, I am about to start a project where I want to control 2 stepper motors (+encoder) in closed loop, using a PID controller.The Process Variable is a analog signal that needs to be...
View ArticleStepper motor control
Im looking to interface with a inkjet printer with a stepper motor in order to convert it to a flatbed printer for printing baked goods with edible ink. (there are machines on the market that do this...
View ArticleConfigure Stepper Drive Fault indicator w/ UMI 7764 and a Kollmorgen P5000...
Hi I am using a NI PXI-7352 with a UMI-7764 connected to a Kollmorgen P5000 Stepper drive Get datasheet here http://www.kollmorgen.com/en-us/products/drives/stepper/p5000-series/p5000-stepper-drive/ I...
View ArticleScan engine in fault mode
Dear all, I am using a CRIO-9075 with a NI9205 and Ni9263 to control the motion of a hydraulic actuator. The actuation and position/force signals are analog. I am using the softmotion library to create...
View Article