ABB PLC module error troubleshooting methode
Dear All, PLC ABB AC500 PM573 CPU module shown Error LED on how can I resolve this problem and what is error massage how can i found. tell me ideas or related documents.
View Articleerror in using softmotion
Hi,when i want to add the solidworks to the project i got this error in the picture ?thanks
View ArticleServo signals running too fast upon restart of VI
Hello everyone, I am working on a project regarding control over a servo motor. However I am noticing an error that I am not able to fix on my own.I have provided the VI and a picture of what happens...
View Articleturn to active mode
Hi,i tried to connect labview with wolidworks but when i tried to convert to active mode i got this problem in the errorcan any one help me ?thanks...
View ArticleThe version of the LabVIEW NI SoftMotion Module installed on the host differs...
Hi,i got this problem when i want to deploy the project with softmotion https://www.dropbox.com/s/at9r9w667i00qja/qqqqqq.pngNI SoftMotion: The version of the LabVIEW NI SoftMotion Module installed on...
View Articlemy labview code and a thirdparty GUI
Hello, I have written a labview code to do data acqustion by using a ni daq device. I need to integrate a motion control GUI which came with the controlboard into my labview code and I was wondering...
View ArticleBipolar stepper motor: how to change direction
Hi!I want to drive a hybrid bipolar stepper motor using a motor driver, a usb-daqpad 6016 and labview 2012 software as the user-interface. The motor driver that I use has 3 pins; enable, direction and...
View ArticleClik here to view.
NI softmotion gives a error when deploying
Hi all i tried the example of getting started with the softmotion for solidworks.. i completed whatever been said in the example its not giving any error until the last step when i press the deploy...
View Articlemotor movement problem with APT actuators
Hi.I have 2 APT DRV013 motors and I installed them to my system.For some reason, I get an error when trying to hold open both a VI that uses the actuators and the APT User program.Does anyone know the...
View ArticleNI 9223
Hi, I am developing code in LABVIEW to control matrix converter in open loop for cRIO 9082 chassis. NI 9223 is used for measuring three phase input voltages to the converter. I am simultaneously...
View ArticleGarbage value at analog output of NI 7350
I am using following hardware and softwareNI7350 controllerUMI 7774Mitsubishi drive MR-J2S-10AMitsubishi motor HC-KFS13Labview 2011Ni Motion 8.3MAX 5.1The problem I am facing is that even when there is...
View ArticleClik here to view.
Read function block in softmotion
hi ,,, i have this Design in solidworks https://www.dropbox.com/s/gc2dubrimo8yrgt/Assem4.JPGi need to read the angel of the pemdulum and show it in the labview using softmotion ..any suggestion plz...
View ArticleSolidworks sensors reading
Hi,how are you? i want to ask if i can read the sensors from solidworks in labview and show the value of this dimention sensor as a numirical value on the front screen of labview ??? thanks
View ArticleCould someone tell me how to control a small dc motor by using labeled and a...
Could someone tell me how to control a small dc motor by using labeled and a NI 6008 daq. The motor is adjustable by using a pot that ranges between 0-V if that is of any additional benefit.
View Articleteleoperation help
Hi everyone! I have a robotic arm that needs to be controlled through a network connection with a joystick. I developed a project where I read every 75ms the axis and the buttons of my joystick and...
View Articleerror 89139
Hi,I have a PCI-6723 and PCIe-6536 and use LabView 2012. I would like to give a time sequence for this two boards and output them. I connect this two boards with a RTSI line to get the synchronization....
View ArticleLabview Calculation Speed
i met a problem in Labview that I want to calculate the energy and distance using integration and feedback in the while loop. But the calculation result is quite different from the real result i...
View ArticleHow can I calculate the peak and RMS torque and velocity in LabVIEW for motor...
Hi all am having problem in using the examples which comes with labview for calculating motor and actuator sizing . am using labview 2013 x32 evaluation version , softmotion 2013 evaluation version...
View Articlefeedback issues
Hi I'm trying to get my system to work. The problem is the output from the initial 'minus' following the simulate signal is zero when it should be a value of 'signal - feedback'. I'm not very...
View Articlecontrol linear stepper actuator with NI myDAQ
Hello, for my experimental application i would need to control linear stepper actuator shown below :...
View Article