Couple questions regarding NI integrated stepper and drive
The first question I have is can you integrate the stepper configuration utility into labview, or do they have to be used as two separate programs? The second thing I am wondering, is what is the step...
View ArticleClik here to view.
What is the speed control logic within NI9514?
Hi guys, I'm using NI9514 to control a servo mortor, but the control logic just confuses me. I used Straight-Line-Move block to give a certain velocity to motor and the motor does follow the...
View ArticleHow to send a step with AKD EtherCAT
Hi,I'm working with a cRIO and softmotion I would like to know how to send a Step to my Engine via AKD. In my tools of Softmotion I have several type of move (Line, Arc, Contour) but I don't have a...
View ArticleClik here to view.
Home switch control during simulation
Hello,I am trying to control Softmotion simulated axis and I am struggling to work with Find home express VI. I have found a nice example project called Reference Move - Home and index. My problem is,...
View ArticleAgilis-P Controller (Model CONEX-AGP)
Dear All,We have bought a linear satge (AG-LS25-27P) with Agilis-P Controller (Model CONEX-AGP). I have an inquiry regarding the VIs (labview) of the controller. Thereshould be several VIs to control...
View ArticleReserved pins in NI9514
Hi guys, I found that there're many reserved pins in module NI9514. Is there any way that reserved pins can be programmatically changed to a analog output or anything like that? Many thanks in advance!...
View ArticleWhy write express vi does not work while line do?
Hi, I'm using NI9514 to control a motor drive. When I was building the VI I found that the straight line move works while the write(with either velocity or position) won't do anything. I've read about...
View ArticleBreakpoint Pin Axis Assignments PXI 7354
Hello,I've had a customer dig a legacy project up from the dead and I am looking for a bit of information on the PXI-7354 / UMI 7774 combo with regards to BreakpointFirst I should say that the code is...
View ArticleLabview based Velocity control linear translation stage XPS Q8
Hello all! I am currently trying to setup a labview based automation for an XPS Q8 motion control, as a part of a project. What I used to do earlier was logged in to the browser based control for XPS...
View ArticleNewport Conex-cc drivers for LabVIEW?
Hello all, I am looking for the Conex-cc labview driver. Please let me if any one knows...... LabVIEW driver manual for more...
View ArticleClik here to view.
How do I control multiple motors using Elmo Gold drives through EtherCAT with...
Hi,I need to control multiple motors using Elmo drives through EtherCAT, the master is cRIO 9039, and now I can control the motor directly connected to cRIO 9039 by net cable(e.g. Address 0 in the...
View Articleimplimentation of a fuzzy logic contro on fpga
HelloI am a beginner in labview fpga and I want to achieve a fuzzy controller to control a DC motor. But I can not find the solution that sancfant that I use a card devlopment "digital electronics fpga...
View ArticleController for NI MID-7604?
I have been assigned by PI to run stepper motors on 3 axis and i have been given the NI MID-7604 stepper motor drive. While I am able to figure out how the encoders work for the most part, I don't know...
View ArticleInterval for contour move
Hi I am trying to code a program to let a single axis run a sinusoidal profile. I used the example "Axis continuous contour move.VI" as my starting point. In the example, there is a "signal generator"...
View Articleuse LabView control newport model 8752 to move one axis picomotor actuator
When I implemented the example there are some errors like Figure(1), and my LabView version is 2018 64-bit . I am not sure whether the dll file is 32-bit? Do I need to recompile the file?
View ArticleMID-7604/7602 Its possible to control without Motion controller?
Hello,For my project, I need to control 2 motors with MID-7604/7602. But I dont have PCI motion controller.And I am interested, its possible control MID-7604/7602 without Motion controller,but using...
View ArticleSMD-7516 Reading the Analog Inputs
Hi all,We have a project in which we would like to make use of the SMD-7615 card and readout the Encoder position as well as the Analog Inputs it has available, as stated in the datasheet. However, it...
View ArticleNI 6034E for motion control?
Is it possible to use the NI 6034E multifunction PCI card for motion control on a 3 axis system?
View ArticleNo encuentro el datasheet de mi stepmotor
Tengo un proyecto de la escuela donde hare una cnc con mis compañeros y un amigo me presto su step motor, y no encuentro su data sheet para trabajar con el, la info que viene...
View ArticleMID-7604/7602 Its possible to control with third party motion controller?
I'm trying to find PCI motion controllers to connect to my MID 7604 power drive. I have been assigned to run 3 axes and the only thing I was given to work the motors is just the MID 7604. I was...
View Article