PCI-7334 Not working As Expected
Hi,I'm using a PCI-7334 with the NI-Motion 17.0. The 7334 controller is new, right out of the box (although it has been sitting in the box in my office for several months). My goal is to use the...
View ArticleMAXON EPOS 4 control using embedded CAN for RIO
I am trying to control a MAXON EPOS 4 BLDC drive using a single board Rio and the embedded CAN for RIO library. I think I am close, but I am not quite sure whether my formatting of the data payloads is...
View ArticleNudrive Amplifier Box
I have a small CNC router that I'm working to get up and running. I'm looking for pdf manuals or documentation for a nuDrive 3 Axis Power Amplifier Box ser# 4067 mod# 3ST-211. The only manual I found...
View ArticleControlling a pump using myRio analog output
Hi,I want to control the speed of a water pump (12V), I am planning to use Ni myRio which has 10V AO pin and I don’t need the pump to operate at its maximum speedIs that possible?Or what other setup...
View ArticleNI 9512 problems with overshooting position
I have inherited some code with a strange bug to do with SoftMotion. We have 4x ISM-7401D motors with non-NI encoders on the shafts. They are driven by 4x NI 9512 controllers sitting in a cRIO 9035...
View ArticleConexiones entre Drive P70360 al Modulo 9512
Hola Necesito conectar un Drive P70360 SDN al modulo NI 9512 pero no cuento con el cable para hacerlo y me gustaría hacerlo yo mismo pero se la relación entre cada uno de los dispositivos.
View ArticleReplacement for PCI-7334
I have a old system that uses a PCI-7334 board to control 3 stepper motors via a nuDrive 4SX-411. I would like to replace it with a newer system. NI discontinued the PCI-7334 product without providing...
View ArticleYaskawa servodrive controlled with s7-1200 via PTO
Hello,My question would seem to be stupid for many of you but i still can't solve it myself. I'm trying to control a servodrive SGDM via PTO.Wiring: i connected the pin 7 to the pulse output on the...
View ArticleTrying to blend straight-line moves with an ethernet connection and...
Hello All, As it says, I am trying to blend multiple straight-line moves together on Softmotion lite, I'm also very new to labview. I have tried using the ExpressVI for blended moves to no success, as...
View ArticleGain tuning panel not present on NI 9514 axis (EtherCAT)
Hi, I'm configuring a new axis with the NI 9514 servo drive interface (analog). The c-series module is mounted on an EtherCAT chassis 9144. Once I bound the axis to the module, I can access...
View ArticleControlling a Linear Actuator through myDAQ (LabVIEW)
Hi, My team is trying to connect an analog chopper drive (linked) to a linear actuator (also linked). We also have an NI myDAQ available to us as an intermediate analog switch. Our ultimate goal is to...
View ArticleNI 9514 in Scan Interface Mode (architecture questions)
Hi,I would like to confirm that I understood correctly how the NI 9514 work. I'm used to build axis that have a trajectory and a supervisory code on the realtime side and an FPGA that do the spline /...
View Article"Write Position Setpoint" Softmotion function not allowed anymore in 2018...
I'm upgrading a code from 2016 to 2018 and I now realize that I can't use anymore the "Write Position Setpoint" fonction is now not allowed with a 951x module. My code use that fonction for proper...
View ArticleSoftMotion timeout minimum value is 1 sec?
Read Motion I/O: Axis Limit Active takes too long.Got invalid value error when set Axis:Timeout to 0.5 sec, no error for 1 sec.Not documented.
View ArticleSMC LECP6 step motor controller help needed
HiCan someone take a picture of the Zener diode behind the rj45 connector on boardIt should be a 3 pin smd sot-23, someone has pluged in a ethernet cable and burned the rs485 portunfortunately I cant...
View ArticleXPS Motion Controller and IMS500LM stage
I have an XPS C motion controller and I am trying to connect it with an IMS500LM stage. I have two drive cards that should be compatible with it and I have the cables that I need to connect it (motor,...
View ArticleGet separately the 3 axis of cell phone's accelerometer
Hello, I have the same problem as the problem in this post : https://forums.ni.com/t5/LabVIEW/Accelerometer-3-axis/m-p/3707391#M1043053but im using my cell phones accelerometer (cell phone: samsung j5...
View ArticlePCI-7340 Operation Mode
Hello, I am using a setup with a PCI-7340 card, NI Motion 18.0, and LabView 2018.I have everything wired and configured correctly and am able to perform position moves as part of a custom test device...
View ArticleLabVIEW Robotics Module Version 2012 Hardware setup error
Hi, I came into the problem of unable to configure my robotics module when using the Hardware setup software, the error code is -2147220308. And there is a call chain :nisyscfg.lvlib:Uninstall...
View Articleerror code -72015
I installed NI Motion 16 driver for PCI-7332 controller that is connected to UMI-7772 interface board. My LabView code is calling nimotion.dll function named nimcReadDigitalIOData(). Testing DIO was...
View Article