Linear servomotor endlimit value reading
Hi Im currently controlling linear servo motor with Labview and ran into a problem. I need to stop the motor immediately when it reaches the endlimit sensor. The problem is, that the endlimit sensor...
View ArticleStarting multiple motors in sequence by one inverter
Hello,I want to use single motor drive to start multiple motors one after another. The procedure would be to start first motor by drive then switch it to direct line power supply by contactor, start...
View ArticleControl VFD (Dayton IP 20 Drive) Using LabVIEW
Would it be possible to write a code in LabVIEW to control this drive? If so, how would one wire the drive in order to control it? Also, would like to take readings through an oscilloscope to watch...
View ArticleBLDC motor with hall sensors control
Hello, I am interested using brushless motor hall sensors as my feedback without using encoder additionaly. My hardware: cRIO, NI-9516 drive interface and an AKD drive to connect the motor. I was...
View ArticleHow many axes can I create on cRIO 9068 and 9042 using SoftMotion Drive...
How many axes can I create using softmotion drive interface with Ethercat (CoE)? What is the maximum frequency can I set on the control loop for the movements? Is there a formula to estimate what is...
View ArticleDelta servodriver using ethercat CoE
Am I capable of read the actual torque of the servomotor while controlling in position or velocity mode?
View ArticleAKD how to change IL.LIMITP
Is there a way I can set and/or read the AKD parameter IL.LIMITP programmaticaly in Labview. This is the application peak current, positive direction.I'm using the NI Softmotion library but doesn't...
View ArticleI am studying about controlling of CNC machine using labview. please help me
Hello I saw this g-code paser vi(labview) uploaded in GitHub. I am studying about controlling of CNC machine using labview.I bought a CNC machine and i have to connect motor of CNC machine with...
View Articlecontrol a centrifugal pump flow rate through VFD
I want to control centrifugal pump flow speed that is used in a system for cooling( same like HVAC). I have the labview example in labview examples (Attached). In this example rotor frequency is...
View ArticleServo Position NI 9516
I am writing a code for a servo project I am working on. I am using a NI 9149 chassis with a NI-9237 Strain/Bridge Module, a NI-9205 Voltage Input Module, a NI 9211 T/C module, and NI-9516 Single Axis...
View ArticleMdrive motor: initializing and running
Hello everyone, I have been using a M-drive 17 plus motor for reciprocation and it was working well running through my attached VI. But, all on a sudden its not working. The left/ right/ jogging (left...
View ArticleDoes anyone have examples about how to use property node and invoke node in...
Hi everyone,I have succeeded in running motors with EtherCAT in LabVIEW. What I'm going to do is to running motors in torque control. I saw instructions here...
View ArticleCommunicate with VIX Parker servo drive from LabVIEW
Hi,I'm trying to communicate with VIX Parker servo drive (VIX250AH) via serial interface from LabVIEW. The Servo drive (VIX250AH) is used to control MX80L linear servo motor. When I try to send any...
View ArticleHow to stop a torque controlled motor with Softmotion
Hi everyone,I am using CRIO-9049 and Yaskawa Sigma-7 motors and EtherCAT drives.Now, I can set the motor in velocity mode and torque mode with property nodes, and the motors run well in both control...
View ArticleHow to stop a torque controlled motor with Softmotion
Hi everyone,I am using CRIO-9049 and Yaskawa Sigma-7 motors and EtherCAT drives.Now, I can set the motor in velocity mode and torque mode with property nodes, and the motors run well in both control...
View ArticleReplacement for PXI-7344
Need recommendation for the replacement of PXI-7344 (last order date is end of Sept.).Need 4 axis step motor control. For 32 bit LabVIEW 2014 or later.NI product preferred.TIA.
View ArticleSoftmotion - Velocity/Time Move Woes
Im trying to conduct a velocity time move in Softmotion such that my move finishes within a set time and follows a custom profile. The motor controls a variable filter which has a logorithmic scale,...
View ArticleCreating UDV Axis, error 6280 in Interactive Test Panel
Hello, I'm trying to deploy an Axis in NI Softmotion. When I open the interactive test panel, I get the fault 6280 : "There was a problem while deploying the User-Defined Variables for an Axis."I'm...
View ArticleBipolar Stepper Motor With Arduino Mega and RobotDyn Motor Shield 2A L298P
I'm trying to use LabView 2018 to control a bipolar stepper motor. I have an arduino Mega 2560 and a motor shield from RobotDyn. Here is the link to the product. I was trying to manipulate the program...
View Article3d
Hi,I have set 3d coordinate points in array and I want plot this 3d coordinate array curve in wrl file as look like cylindrical curve. If any one knows please help how to plot.
View Article