NI-PCI-7332 onboard programming capability
The NI-PCI-7332 datasheet specify this controller board have the onboard programming feature but I can't find any example where it is used with this controller (most examples use the 7340). When I...
View ArticlePCI 7342 controlling the digital ports with MAX
We see how to initilize the PCI 7342 digital ports with MAX, but how do we actively toggle them with MAX?
View ArticleCCC Certification
Hello - We make equipment that has MID 7604 drives and PCI-7344 cards embedded in it and need the CCC Certification for Chinaelectrical product imports. Who has this? It is a certificate that shows...
View ArticleF502 DC bud undervoltage
I am using a Kollmorgen AKD drive (model: AKD-P00306-NAAN-0000) and it keeps showing a DC bus undervoltage error (sometimes after a very quick F302 motor overheat error, even when the motor does not...
View Articlebreakpoint max modulus only (2^14-1) not (2^15-1) as per references
Hi,I'm using a PXI-7352 and am happily doing periodic breakpoints using C code, but when I tried to use a larger bp modulus (flec_load_bp_modulus), I get an invalid value error for any modulus value...
View Articlehow to move AKM motor with AKD drive continuousily
Hi everyone, I have an issue with controlling an AKM motor using an AKD drive with ethercat a, NI softmotion and crio 9064. Actually, I have a for loop and i want to send the same position to the...
View ArticleHow to use 9512 in FPGA Mode?
Hi, I have two NI 9512 in a 9030 cRIO Chassis. I have successfully created a new project, added my cRIO, added two Axis configued them and run up the interactive test panels. My Stepper motors are...
View ArticleTDC001
Hi, I have two TDC001 in which required to control by the same program. The error would be appeared as soon as I pressed the button to run the program. One of the motor started to move without...
View Articlerobotics
I'm working on an instructional robot using the Tetrix/Lego NXT system. I can't understand why the Labview VI for the motor controller delivers an error (Motors: multiple controllers specified) when...
View Articlemultisim (field winding)
Does anyone know where in multisim 13 I can find a field winding (coil) and dc motor armature? I am trying to simulate a separately excited dc generator.
View ArticleTST101 APT Motor Control Help
Hi there! I have a TST101 (https://www.thorlabs.com/thorproduct.cfm?partnumber=TST101), that I am trying to operate through LabView using Thorlabs APT software. I have run through the Example.VI listed...
View Articleapt
Hi, i am trying to control two waveplates from a Labview program. I am using the Torlabs MG17 Motor Controlled package but I am having a problem. One of the waveplates is well detected by the Motor...
View ArticlePCI-7344 Homing on continouse rotational axis
I am trying to calibrate a rotating axis that does not have any physical stops but I need to know where I am at on the 360 degrees I am working with. It seems that all limit and home inputs actually...
View ArticleClik here to view.
how to program an epos2 controller over labview?
hello, i want to run an epos2 24/5 positioning controller from maxon motor over labview. i already have the epos toolpalette in labview but can't find any programming examples or explanations. does...
View Articlerobotics module in fpga
I am working in LAbVIEW fpga for a robotic arm control (cRIO 9024) . I wish to use the forward kinematics block but it is available only in RT platform. Is there any other method I can use Robotics...
View ArticleUsing Softmotion won't enable my drive for control?? What can be done to...
I'm using a 9512 stepper control module to control a motor through a third party drive (GeckoDrive G213V) and the problem I've hit with using softmotion is that I can't get a "Drive Enabled" state from...
View ArticleSoftMotion Error -70216 when starting absolute straight-line move
When I start an asynchronous straight line move using softmotion express straight line absolute move, the VI is throwing error -70216 sometimes (not very often but within 24 hours it will definitely...
View ArticleClik here to view.
Newport SMC100 raises Error 7 after compiling + solution
In a test program I tried to open and close the communication to the Newport SMC100 translation stage controller, using an RS232 connection. When I run the program in LabVIEW it works properly. When I...
View ArticleAcquired image coordination
Hi Everybody My project is about the detection and tracking of fast moving puck on air hockey table. I need to detect puck(as foreground) and track its movement on the table. I need to coordinate the...
View ArticleConfigured axes not being included in built executable
I am using SoftMotion Lite to control 4 stepper motors via an expansion chassis. When running my application within LabVIEW, everything works fine. All motors work exactly as expected and I have the...
View Article