Differences between Dynamixel MX28 servo control and MX106
I have just received a couple of MX106T Dynamixel servos (get to play with torque control!).Is there a difference between initializing for the MX28 and the MX106? I can't find any data on that... right...
View Articlesoftmotion software problem
Hi guys, I am trying to run my softmotion by following this link from getting started with ni softmotion " http://www.ni.com/white-paper/9566/en#toc1 " but when i try to open "New»SolidWorks Assembly"...
View Articlewhat interface device shall i use?
Hi guys, I am a mechatronics engineering student and i am currently doing my final year project which is developing analog controller for inverted pendulum system. i did the mechanical design through...
View ArticleCan I disable host bus interlock on UMI 7764?
I have a multiaxis system (3 x PCI 7334 cards, 1 x MID-7604, 2 x UMI 7764 and 8 x third party amps connected to the UMIs) where I use the Inhibit inputs and the Inhibit outputs for thermal management....
View Articlestepper motor control
Hello,Im very new to labview. As a part of a project I'm trying to control a stepper motor using labview to run a syringe pump (basically to control the speed and direction of the motor). I do not have...
View ArticleHigh-speed sinusoidal motion control with LoadTargetPosition.vi?
Hello,I have a linear stage that I'd like to move sinusoidally at frequencies of up to 100Hz. I'd like to determine the best way to accomplish this. Here's one idea I had: generate the sinusoidal...
View Articlerunning two motors in the reverse directions
Hi,I am controlling two step motors with the vi I attached in the post. This application runs the motors seperately. But I want the left pusbutton to run the first motor in the forward direction and...
View Articlestepper_motor_42bygh404
hi there!i have a stepping motor 42bygh404 (like here http://www.web-tronics.com/nema_17_stepper_motor_42bygh404.html) and i need to control it through LabView.i'm gonna to use it for a neutral filter...
View ArticleAKD Drive Ethercat Torque Mode
I know that similar questions have been asked before without a satisfactory answer (thread), but we are trying to operate an AKD drive in torque mode over an EtherCat interface using a cRIO-9022. I...
View ArticleI can't seem to find a labview driver for the product REL-230-18;
I have a controller made jointly by Harmonic Driver and Copley Controls. I will be controling it through my serial port. I can't seem to find any labview driver for it. Anyone know if I can find one or...
View ArticleUnable to undeploy SoftMotion axis: Hex 0x80004005
Hello, I was using a cRIO-9076 + NI 9505 + SoftMotion for a project. Now, I'd like to reuse the hardware for a new project. The old project had a SoftMotion axis (Unbound), which is refusing to be...
View ArticleLabview code for scanning feed
Hello, I'm working with a microscope with a camera attached that transfers the feed to my pc. In my samples, there are parts with different intensities, and I'm interested in using Labview to...
View Articlehow to check a incremental encoder by multimeter
hi i have a robotic machine i am facing problem in one convyer that convyer not taking step i have a dout on encoder i want to check that encoder by multimeter how i can check it encoder make --...
View ArticleWatchdog timout errors on NI-7356 (-70035 NIMC_watchdogTimoutError)
Hi, I have a test setup based on a NI-7356 controller. It controls 6-axis, performs contouring and high speed capture. I have two types of watchdog errors:1. The computer has to be cold started twice...
View ArticleWarning while loading example VIs for XPS motion controller
Hi, I'm new to Labview. I want to control the XPS motion controller using Labview and I wanted to get started with the examples provided by XPS along with the drivers. But I get a warning while loading...
View ArticleAMSI 8003-DM Compatible?
I am curious as to whether the AMSI 8003-DM stepper motor driver is compatible with your products. I have noticed that the website that was supposed to hold the original software to control it is gone...
View Articlelabview interface arduino
Hi, I am using Arduino with LabVIEW to automate an extruder machine for my masters project. Can you please tell me how to obtain wire diagram for the Arduino circuit after completing the graphical...
View ArticleNI 9263 - Run a small DC motor with the analog output from the NI 9263
First off, I am very new with LabView and the NI DAQ system. I have been trying to connect a small DC motor to the NI 9263 Analog Output Module, but have had no luck in getting the motor to run. Could...
View Articlespeed and position control in a servo system?
i need to be able to manually control the speed and position of a servo motor while the motor is working. the manual part is operating some sort of position switch or sensor. basically i want to move...
View ArticleDifference between 'Positioner Group Move Absolute' and 'Single Axis Group...
Hi, I am using an XPS C8 controller with 2 linear motion groups. What is the difference between 'Positioner Group Move Absolute' and 'Single Axis Group Move Absolute' Vis?
View Article