NI SMD-7613/7614/7615/7616 Stepper Motor Drives - comparizon Table
Sorry for my obvious question, but where on NI Web page can I found full list of the NI Stepper Drives with all parameters?Like NI SMD-76* Stepper Motor Drives. I have seen some info few years ago, but...
View ArticleLosing induction motor max torque
Hey, I have two Leeson 3 phase induction motors that are set up on a materials shredder. The motors are rated at 1740 rpm, 230V, 3hp. I am having trouble shredding a 2 by 4 piece of wood and I think I...
View ArticleNI-7340 limit and home switch indicators always active using NI Max
Working with a system that is using an NI-7340 controller to drive stepper motors and using NI Max to checkout the motor operation. Earlier in the checkout process NI Max allowed motor operation with...
View ArticleThor Labs Motor - Labview Error
My lab is using Thor Labs motor controller on our device. The labview code is a series of for-loops, moving our platform in the x, y, z direction. The program keeps generating this error message and...
View ArticleNI PCI 7390 Error 70207 NIMC_inhibitInputActive Error
Hi! I am working on a 3D Printer that uses an NI PCI 7390 card. However, I keep running into an error upon initialization of the controller which states that the move cannot be completed because the...
View ArticleHow can I control a burkert valve 3280 by LabView?
Hi,I would like to know how to control a burkert valve3280 H 8.0 FKM MSG1/2 PN 6bar24V C 12WThe valve is connected to a condenser, and I want to control it according to the outlet temperature by using...
View ArticlePXI 7340, UMI-7774 Not Fully Functioning
I have three ISM-7400 stepper motors connected to a UMI-7774 interface which is connected to a PXI 7430 controller. All three motors are wired identically with identical switch settings. Some channels...
View ArticleNuLogic Driver Disk for PC, Version 5.8 (for nuLogic pcControl-4a isa board)
Hello friends, does anyone have NuLogic Driver Disk for PC, Version 5.8? I need it to configure nuLogic pcControl-4a isa board on a vintage PC with Windows NT 4.0.
View ArticleNI power electronics programme example code
I have NI 9606 board with NI 9683. 1.I don't know how to add NI 9683. In project I can find NI 9606 FPGA but IO ports of NI 9683 is not showing. Please help how to add this module in project. 2. How...
View ArticleCan't find .flx files for legacy software
Morning all - I'm trying to edit a legacy LV, but am getting errors saying that the .flx sub-VIs cannot be located, preventing me creating a new executable of the legacy software. I have a fresh...
View ArticleOptidrive E3 compatibility/connection to LabVIEW
I've been trying to find information on the NI website to determine if the Optidrive E3 Modbus is compatible with LabVIEW. If anyone can point me in the direction of the documentation I would deeply...
View Articleservo experiment station
HiMy name is Assaf Keller, and I am planning to build an experiment station to control several servo motors through scripts on my laptop. I am interested in measuring various parameters such as:Current...
View ArticleAsking about Attocube controller
Hi, I have a Labview code written for Scanning Probe Microscope, to be precise, for AFM. In the code for coarse motion motor driver (X,Y,Z for three axis excitation) is used but I want to use Attocube...
View ArticleSynchronize two analog outputs with different sample sizes and rate of outputs
I am using a PCI 6321 to run a scanning microscopy setup and would appreciate some advice on a technical issue with timing the DAC for acquisition (output). I have a problem synchronizing two different...
View ArticleEtherCAT communication with CU320/S120 from PXI
Hi everyone, I am trying to control siemens drives through a labview project, over etherCAT. I have in my possession a CU320 equipped with the S120 Robox card, to interface with etherCAT comms. I have...
View Article