USB Motion Card STB4100
Hi all, Sorry, I'm a beginner. So my question might be simple. Is there a way to control the USB Motion Card STB4100 with Labview? Is there a library? Thanks for any helpBest, J
View ArticleSelecting a motor for a NI9503
Dear experts;In choosing a motor to run with a NI 9503 powered by +24V; my colleague has purchased a 3.5V stepper motor (datasheet attached). His feeling is that since power is applied for a fraction...
View ArticleCRIO, Compax3, EtherCAT, servo loops
Fairly simple application.6x Parker Compax 3 DrivesEtherCAT communications to NI CRIORead feedback from drives - velocity and current torqueCommand drives - torque command into torque...
View ArticleBSC203 motor is not appearing in APT config
Hello everyone, I am quite new with Labview and APT so I would really appreciate your help. I installed Labview 16 (64-bit) on my 64 OS laptop. I have a new set up in my lab with a BSC203 controller...
View ArticleControlling a Servo Motor and Driver with NI USB 6001
Hello, I would like to obtain some advice about a set up that I would like to implement. I am going to be using a servo motor package from Anaheim Automation (datasheet attached), and I have some...
View ArticleBrushless DC motor using NI 9502
Hello,I want to use NI 9502 module to control brushless dc motor.Several questions, 1. In the Datasheet it is recommended to use both NI PS-16 and NI PS-15 power supply's. The first will be used for...
View ArticleControlling 4 stepper motors for 3D printer using my-rio FPGA
Hello, I have a project to control 4 stepper motors for a 4 axis 3D printer. I know using soft-motion one can control the motors by defining the axes. But I want to use my-Rio for this purpose. I am...
View ArticleLabVIEW
Hi, how do initial gains in pid fpga express vi differ with gains in front panel control? where should I assign pid gains achieved from tuning pid to implement pid controller on fpga target?Thanks!
View ArticleClik here to view.
NI 7352 (PCI) Not Initializing. Error - 70035{Watchdog_Timeout Err}
Hello all,We have a NI 7352 (PCI) Motion controller with windows 8 pc. While powering on the system most of the times we are experiencing an error at startup. The NI MAX error codeError -...
View ArticleControl Stepper Motor via DM452T Controller and Arduino
Hello,I am working on a project to control a stepper motor via labview with arduino's help. I am not an expert in labview so I need some help with programming and if someone used the DM452T can tell me...
View ArticleClik here to view.
Dynamixel motors control using Labview SDK
Hi everyone,I need to control 3 Dynamixel MX-64AR using Labview SDK. I already donwloaded the Dynamixel SDK file and found its Labview files. Then I did a reasearch on the net to follow all the steps...
View ArticlePCIe DAQ for closed loop control. Max hz.
Hello, I'm just getting into lab view, NI hardware and want to set up a system to do some fast motion control.I'm hoping to use a PCIe6353 to run 3 PID controllers in parallel on a very fast CPU.I'm...
View ArticlePCI-7342 can't achieve smooth velocity at 1 count/s
Hello, my motion setup is a DC brush motor with encoder, linear servo drive, linear regulated DC power supply, and PCI-7342 with UMI breakout board. In the user manual for the 7342 card, I read that...
View ArticlePCI 7342 with UMI 7772 setup for Delta servo drive ASDA-AB (UMI-7772 issue?)
Setup:PCI-7342 motion controller card with UMI-7772 to interface with two delta electronics servo motor drive (ASDA-AB). Issues:1. UMI is not behaving as mentioned in the user manual:a. After disabling...
View ArticleResolver, Axial motor zero position offset
Hi,We are using a resolver for our axial type motor. Our customer requested for the following details-position offset in degrees between the resolver's mechanical zero position and the machine's...
View ArticleHow to control (PID) the position of DC Motor by using Labview, NI USB 6211...
Hi all. I am fairly new with NI-DAQ and Labview, doing a project to control the position of a DC motor by using a Labview software, NI USB-2611 and Throttle Position Sensor. The motor is controlled by...
View Articlehow to write cost function in MPC
Hello everyone.. I need little guidance please .... JI have attached image of equations, i want to implement MPC but don’t know how to write cost function. In equation (11) energy of fan is written ,,,...
View ArticleStepper motor control with Limit Switches
Hello All, I'm new to LabView so I apologize if anything I say comes across as confusing. I'm in need of some help developing a program to move a sample plate using stepper motors inside an instrument...
View ArticleMisumi motorized stages
Hi, I'm trying to get a handle on some potential changes to an x-y motion platform. The system uses 2 of the Misumi RS1 linear stages with the C1 type controllers. My Misumi P/N is RS102-C1-N-3-200...
View Article