Configure NI9512 and P70530
Hello, I´m a new programmer in LabView. I would like to drive with two stepper motors (Unipolar) a definied XY-Profile.For this project i have: -NI9512 (2x) - P70530...
View ArticleMotor Position Control with NI PCI-6035e?
Hello all, I have a NI PCI-6035e card from a previous project that was used for reading analog inputs on a tensile test frame in conjunction with an exteral motion control unit. I have been tasked with...
View ArticleAre the SH68-c68-S and SHC68-c68-S cables interchangeable?
The SH68-C68-S is specified for the UMI-7764 and the SHC68-C68-S is specified for the UMI-7774, but are these cables both compatible with the UMI-7774?Thanks.
View ArticleTension control in labview using PCI 7354 Motion Control Board
I want to make a program for web tension control of roll to roll system in labview using PCI 7354 Motion Control Board. Is there any interface program that can convert my controller output in a format...
View ArticleLinearmotor not running
Hello, I have got a (4 pieces) linearmotor and have to use it with the PCI7350. When I disable the inhibit output, I can enable the Motor with a simple LV program and can swith the controller into the...
View Articlehow to measure torque of servo motor
Dear Experts, i want to plot a speed torque characterstics in labview using ni hardware with servo motor. please suggest me complete solution for this above question
View ArticleStepper Configuration Utility Software?
Hello, I am trying to get a stepper motor rig up and running and I am having an issue. My setup and the process I am following is best described by this pdf:http://www.ni.com/pdf/manuals/376090a.pdf...
View ArticleDual Stepper Motor Controllers on a CAN Bus
Hello All, Friends of mine are working on a project involving controlling many dual-stepper motor assemblies, using LabVIEW as the main control code running in the control hub computer. The stepper...
View ArticleClik here to view.
stepper motor overheat
Hi all, I'm using the legacy motor CTP10xxx10 with motor drive P70530, on page18 the manual says "...If an equivalent heat sink is not used, reduce the default drive current for these motors by 25% to...
View ArticleVariate velocity according to position
Hi all, I'm now using PCI7330 with P70530 to control the stepper motor CTP10XXX10. My goal is to let the motor run at certain speed as a function of its current position. Is this possible to read...
View ArticleSoftmotion error –77055
I'm working on a softmotion RT application. I have a CRIO(9074) and an EthernetRIO (NI-9146) to control 5 independent axis. 4 of those axis are exact copies of each other (code wise and hardware wise)...
View ArticleContinuous, triggered, high-speed motion capture
Hello, I'm attempting to perform a continuous triggered high speed motion capture independent of the motion, and it's not clear that this is possible. Before I spend a few hours on a wild goose chase,...
View Article7344 FlexMotion32.dll
Hi, After many years I am getting around to using my 7344 PCI motion controller board... I am trying to find the DLL to call from my C# program.. Where can I find the FlexMotion32.dll And I heard that...
View ArticleFind Reference with gearing Error 70166
Hello, I have an xy-Table with 2 linear motors per axis. The motors of one axis are fixed together. An axis is configured with gearing (X: master: axis1, slave: axis2; Y: master: axis3, slave: axis4;)....
View ArticleThorlabs TDC001 Controller on Mac-Communication Directly Through USB
I recently purchased a TDC001 controller from Thorlabs and I am trying to use Labview with it. But I am currently operating on a Mac which Thorlabs does not cater to because they only offer the Windows...
View ArticlePCI-7354 axis enabling
I'm having an unusual problem that hopefully has a simple solution. I am using VB6 to make an ActiveX DLL that is called from a VB.NET 2010 application. This is connected to the motor by an NI...
View ArticleNI 7330 closed loop control mode
Hi, Iam trying to operate NI7330 in closed loop mode from MAX. I tried to do the steps as described in the page shown below. http://digital.ni.com/public.nsf/allkb/9675C83F037811F68625727C0002A4A5 I...
View ArticleUsing NI 9512 with Position Step Frequency Modulation? (cRIO)
I am attempting to power a stage for an experiment that requires a frequency modulation on the step signal sent to a stepper motor. I am using a cRIO-9076, an NI-9512 and a NI P70530 stepper driver to...
View ArticleKollmorgen Motors with PCI-7342 and UMI-7772
Hi,I am trying to connect a pair of third-party servo-motors (Kollmorgen AKM11B-ANCNC-00) and drives (Kollmorgen AKD P00306-NBAN-0000) using a National Instrument motion controller NI PCI-7342 and...
View ArticleNI Stepper motor
Hi all, I wan t to have an stepper motor with a built-in encoder. something like ST34-8E from NI. But I'd like to know if it is crucial to drive that buy NI products or I can use any other third party...
View Article