Stepper motor with 6009
Hello All, i need to run stepper motor (4 wires) with 6009.Between 6009 and stepper is SN745510.I need to run motor continuosly, some numbers of turns.I wrote some VI, but i don't know how to control...
View ArticleNeed a Comprehensive List of Vibration-Diagnostic Rules.
I am a Software developer. Recently, I have been assigned a project where I need to develop a Vibration Analysis Software for condition monitoring of some motors. One of the "Terms & Conditions" of...
View ArticleNI SCC-68 for motion control?
I cannot afford to get a universal motion controller but I found the SCC 68 terminal block. I know it is used for Data Acquisition, but i was wondering if there is a way to connect it to a stepper...
View ArticleCONEX-LTA-HS incremental delay with 433 and 9848-KT
Dear good people,I have a 9848-KT (retro-reflector), that has been mounted on a 433 (stage) with two gold mirrors, and is controlled by a CONEX-LTA-HS (motion controller) in an attempt to construct a...
View ArticleUsing ESCAPE key to stop a moving satge
Hi,I need to use ESCAPE key to stop a moving stage, and tried different ways, no one worked out. 1. I tried to write ESC string in code format, 2. I tried to write 1B in Hex format,3. I tried to write...
View ArticleCalculate the peak and RMS torque and velocity in LabVIEW for motor
Hi everybody, i'm having project motion motor with labview and solidworks. Now, i don't know calculating torque and velocity. I find project "Cell Phone Test Machine Advanced", but it's error. I will...
View ArticlePWM issue using PCI7344 with UMI-774 from MAX and motion assistant
Hi,Setup:I am using PCI-7344 motion control card interfaced with UMI-7774 to control 4 servo motors. I configure the Axis from MAX software as servo and enable PWM from PWM settings. I have placed an...
View ArticleHow to contorl muti-axis by canopen with NI9881？
Does anyone have experience about control muti-axis at one time?
View ArticleHow to calibrate analog out voltage of ni-7344 in Labview?
HI,I have NI-7344 motion control card. I have limit the DAC output to +-5V from MAX software. Now the issue is how to calibrate the counts to voltage? I don't find any setting for lets say 1000 counts...
View Articleerror -70229
We are currently using the compact Rio and Elmo motion control driver to control the motor via EtherCAT communication.I am using NI softmotion during this process. I added cRio in Labview's project and...
View Articleerror -70229
error -70229 has been encountered and is listed on NI support. First, we changed the scan engine to active mode, reformatted the compact Rio, and installed the software again. We use the NI cRIO 9035...
View ArticleGet Velocity from Motors VI
In theGet Velocity from MotorsVI, how did he convert the speed into a distance? The code of the DC motor I got did not know how to convert it into a distance.
View ArticleAnalog amplifier/drive for UMI-7774
Hi,I am using NI-7744 motion control card with UMI-7774. I want to control NIDEC DC Servo Motor. Can anyone suggest analog amplifier/driver to be used to control the motor?Regards,
View ArticleNI 9514 to control a brushless servo motor
I am looking to control a brushless servo motor (continuous current 5.4 A) using NI9514. I'd like to know if its possible in the first place?Also, to drive this motor, what driver can I use? I am...
View ArticleGalilTools - learning the programming
Hello,I am working on a project that requires me to modify movements of a Newmark XY Gantry machine using GalilTools. The machine is coupled with NSC-G series controller supplied by Newmark, which...
View ArticleUnexpected behavior of PFI ports on USB-6343
I am trying to control three stepper motors to step through a 3d space Goal: Iterate through a series of steps. At each step move only ONE of the three motors. I use a case structure to determine which...
View ArticleSimulating a NI 9684
Hi, I'm trying to simulate a NI 9684 (GPIC), to do some development without the hardware. Would anyone know how to do this? I can add the sbRIO of choice (a 9607) and add a simulated FPGA target to...
View ArticleUSB-8476 NI-CAN vs USB-8506 NI-CAN interface speed
What is the difference between the speed of the LIN-communication signal when I use the USB-8476 NI-CAN and the USB-8506 NI-CAN or NI-XNET as the interface?
View ArticlePCI-CAN/2 Series 2 - Windows 10
Hi, we got a PCI-CAN/2 Series 2 which is installed on a Fujitsu D3646-S1 Board.The card is not recognized in the device manager. Shouldn' t it be at least visible in the device manager even if there...
View ArticleCanopen error mit Canopen Type Def und Canopen Interface control
Ich habe so einen Fehler bekommen. Wie kann ich das lösen?Und ich habe auch gefunden dass CANopenllb kein CANopen Object.ctl hat.
View Article