Problem with EASII and Composer 2 by elmomc
Hi everyone. I'm having a big problem with an Elmo mc servo drive. It's the SimpliIQ Solo Guitar. I have a robot that uses three of these drives. The robot's supplier went bankrupt, so if one breaks, I...
View ArticleLeap Motion Controller find:(
Can you guys help me to find somewhere that sells leap motion controller 1 in 2026? I'm building a project like Tony Stark and rlly need it. I'm still a student so my budget is only 76$
View ArticlePCI 7334 error -70206 (NIMC_invalidLicensingInformationError) after the...
This is an older test system with NI-Motion 8.51, NIDAQmx and Windows 7. A PCI 7330 appears in the Windows Device Manager. It also appears in MAX, but cannot be accessed. Under NiMotionDevices, it is...
View ArticleLooking for LabVIEW Consultant – Servo Drive Control for Industrial Machine
I am seeking an experienced LabVIEW developer for a tester control project involving AutomationDirect servo drives. This is a real, fully operational industrial machine (not an academic model).Scope...
View ArticleHow do I commission a new kit motor to the Siemens 611u drive, 2004 version.
2004 awea mill.Siemens drives and motorsKit motor for spindle.Has been rebuilt and now I need to commission the motor to the 611u drive to make it work correctly.Have the simoconu software. Can ANYONE...
View ArticleIncrease the value of "Following Error" from defult 1000 to 30000 in Labview...
Hi all, I have been working with a PCI-7340 card to simultaneously control four motors. At this point, I can successfully configure all parameters in NI-MAX and operate the four motors without issues...
View ArticleServo Motor Speed Discrepancy Issue with PCI-7340 in Velocity Mode
Hi all,I’m currently using a PCI-7340 card to control four servo motors and have been troubleshooting an issue for some time. When I use the “1D Interactive” function in NI-MAX to configure one of the...
View ArticleControlling Maxon Motor + Encoder with AccelNet BPL-090-14 via LabVIEW and DAQ
Hello everyone,I’m working on a project where I need to control a Maxon DC motor (with US Digital encoder) using a Copley Controls AccelNet BPL-090-14 servo drive. I’m trying to figure out if it’s...
View ArticleEncoder configuration of PCI-7344 in MAX for position detection
Hi all, I’m having trouble configuring a Baldor M3714T servo motor in NI-MAX. I’m using an older Windows XP machine with a PCI-7344 card, along with LabVIEW 8.6, DAQmx 8.7.2, NI-MAX 4.5, and NI-Motion...
View ArticleStepper Motor Control with NI Hardware
Hi everyone,I'm currently working on a project involving stepper motor control using NI (National Instruments) hardware, specifically a myRIO and LabVIEW. I'm using it to drive a NEMA 17 motor via a...
View ArticleCanOpen with ELMO Motor Torque Mode
Hello Dear Forum Members,I want to use my motor, which is elmo, in torque mode.I never made any application like this, so i need your help.With my code, I'll send these parameters for init the motor at...
View ArticleMotion Control and Motor Drives
Hi, I have a Labview code written for Scanning Probe Microscope, to be precise, for AFM. In the code for coarse motion motor driver (X,Y,Z for three axis excitation) is used but I want to use Attocube...
View ArticleCommunication with Compax3 via RS232
Good afternoon,I’m new to the world of LabVIEW. At the university, we are trying to control a servomotor using the Compax3 through LabVIEW. The problem is that we haven’t been able to establish...
View ArticleEnabling AKD drive without SoftMotion Module
Hello everyone, I have an AKM motor and an AKD servo drive (slave) connected to a cRIO-9045 (master) over EtherCAT. I have previously used the NI Softmotion Module to enable the drive and perform...
View ArticleNI-9512 fault when idle
I have a stepper motor that I am operating to rotate a wheel using an NI-9512 module. When operating the motor, everything works fine. However, the longer the system is left to idle, the higher the...
View ArticleEtherCAT communication with CU320/S120 from PXI
Hi everyone, I am trying to control siemens drives through a labview project, over etherCAT. I have in my possession a CU320 equipped with the S120 Robox card, to interface with etherCAT comms. I have...
View ArticleSynchronize two analog outputs with different sample sizes and rate of outputs
I am using a PCI 6321 to run a scanning microscopy setup and would appreciate some advice on a technical issue with timing the DAC for acquisition (output). I have a problem synchronizing two different...
View ArticleAsking about Attocube controller
Hi, I have a Labview code written for Scanning Probe Microscope, to be precise, for AFM. In the code for coarse motion motor driver (X,Y,Z for three axis excitation) is used but I want to use Attocube...
View Articleservo experiment station
HiMy name is Assaf Keller, and I am planning to build an experiment station to control several servo motors through scripts on my laptop. I am interested in measuring various parameters such as:Current...
View ArticleOptidrive E3 compatibility/connection to LabVIEW
I've been trying to find information on the NI website to determine if the Optidrive E3 Modbus is compatible with LabVIEW. If anyone can point me in the direction of the documentation I would deeply...
View Article
![[-100%] Commodity Intelligence – (Android Apps)](http://play-lh.googleusercontent.com/j67-qJvmnn4xnVlYVZ9ZhtZUJIgwjKekJGoKQT6D1KHcWGZxtQaFroummEvwV17na7tyh1pGbbeWCRdWtTKqeg=w950-h950)